The settings for Box Assembly - Wall Cabinets, are the measurement settings of all components of the Upper, Straight Corner, 90º Corner, Oblique and Curved modules.
Check below the definitions of each configuration available in Dimension Configurator - Bedroom - Cabinet Assembly - Wall Cabinets. If necessary, see here how to apply dimension settings.
The available configurations for the Bedroom library top box mounting are:
|
|
Side Panel Attach - Bottom Panel
A - Base Panel advance over Side Panel: sets how much the base panel advances over each of the module's side panels.
B - Side Panel advance over the Base Panel: sets how much each Side Panel advances over the module's Base Panel.
Side Panel Attach - Top Panel
A - Bottom Panel Advance over Side Panel: sets how much the bottom panel advances over each of the module's side panels.
B - Side Panel advance over the Bottom Panel: sets how much each side panel advances over the module's Bottom panel.
Side Panel
A - Gap: sets the spacing of the side panel in relation to the front of the module, the back panel of the module or both.
B - Alignment: defines wheter the side panel spacing will be in relation to the back panel of the module, the front of the module or the center.
Bottom/Top Panel
Gap and Alignment - Bottom/ Top Panel
A - Base Gap: defines the distance of the bottom base from the front of the module, the back of the module, or both.
B - Top Base Clearance: defines the distance of the top base in relation to the front of the module, the back of the module or both.
C - Base Alignment: defines whether the distance of the bottom will be in relation to the back of the module, front of the module or by the center.
Back Panel
A – Back Panel Retreat: defines the bottom offset in the module depth. Applies to all types of funds.
B - Back Panel advance over Base Panel: sets how much the back panel advances over the bottom and top panel of the module.
C - Back Panel advance in Side Panel: sets how much the back panel advance over each of the module's side panels. in the Cabinet Builder modules.
A - Back panel advance over the Partition: sets how much the back panel advance over the fixed partitions in the Cabinet Builder modules.
90º | Oblique | Curved Corner
Corners
Corner Type
A - Corner Type: sets the assembly type for the back panel on 90º corner, Oblique corner and Curved wall cabinets.
With Batten
B - Batten width: sets the width of all the batten on Blind and Oblique Corners.
C - Batten's depth: sets the depth of all battens on 90º and Oblique Corners.
D - Back Panel advance over Batten: defines the advance of the back panel over batten.
Doors
E - Door A Internal Space: sets the internal distance of the A door of the 90º corner with 2 doors for wardrobes.
F – Door B Internal Space:sets the internal distance of the B door of the 90º corner with 2 doors for wardrobes.
W/o Batten
G – Base Panel advance over Back Panel: defines the advance of the bottom and top panel over the back panel.
H – Back Panel advance over Base Panel: defines the advance of the Back Panel to the bottom and top panel.
I – Back Panel advance over the Back Panel: defines the advance Back Panel over the Back Panel.
Oblique Corner
J - Spacer Depth: sets the depth of the spacers of the oblique corners. The oblique corner spacer is applied through the Inserts tab, enabled by selecting the module.
90º
A - Base Type: Defines whether the bottom will be single or bipartite.
B - Shelf Type: sets if the shelf is single or split.
Wall Spacing
A - Lateral spacing: sets the spacing between the module and the lateral wall.
B - Rear Spacing: set the distance between the module and the back wall.
Blind Corner
Corner
A – Tipo Frente Falsa: defines the Blind Corner Panel type for the blind corner cabinet. Whether it will be full, or partial double.
B - Blind Corner Panel advance over Top Panel: defines how much the blind corner panel advances over the module's top panel.
C - Blind Corner Panel advance over Bottom Panel: defines how much the blind corner panel advances over the module's bottom panel.
D - Blind Corner Panel advance over Side Panel: defines how much the blind corner panel advances on the side panel of the module.
E - Blind Corner Panel Retreat: sets the displacement of the blind corner panel on the module depth.
F - Use the spacer: sets the use of the spacer.
G - Blind Panel advance over the Spacer: sets the advance of the blind panel over the spacer. Setting enabled only for whole false front type.
H - Spacer advance on blind panel: sets the advance of the space over the module's blind panel.
I - Spacer advance on shelf: sets the spacer advance on the module's shelf.
J - Shelf Retreat: sets the distance between the module and the beginning of the shelf on wall blind corners. Changes the depth of the shelf. Determines the depth of the spacer used for the hinge's attach.
K - Door advance over Blind Corner Panel / Partial Blind Corner Panel: sets the spacer advance on the module's shelf.
Fillers
A - Filler Type: sets the module's filler orientation. Whether it will be side or front.
B - Frontal filler Spacing | Partial Double Blind Panel Dimension: sets the spacing for the frontal filler in relation to the whole blind panel or the partial double-blind panel dimension.
C - Frontal Filler Dimension: sets the dimension of the module filler.
D - Top Filler: inserts the top filler on Blind Cabinets.
E - Bottom Filler: inserts the inferior filler on Blind Cabinets.
F - Back Filler: inserts the back filler on Blind Cabinets.
Wall Spacing
A - Lateral spacing: sets the spacing between the module and the lateral wall.
B - Rear Spacing: set the distance between the module and the back wall.
