Verifique abaixo as especificações e configurações disponíveis no plugin Profit H08:
Disponível a partir da versão: já disponível
Tipo de máquina: Centro de Usinagem CNC Nesting
Fabricante: Format4
Extensão do arquivo gerado: .tcn e f4g
Manual: manual disponibilizado pelo fabricante, clique aqui.
Principais características
- Furos
- Rasgos
- Usinagem
- Nesting
Configurações
Para verificar as configurações sobre Máquinas CNC, clique aqui.
Arquivo
Define quais as colunas que vão para o arquivo de Nesting. Para mais informações,
clique aqui.
Etiqueta
Define as propriedades da etiqueta da máquina.
Configurações da Imagem
Altura (px): determina a altura da imagem.
Caractere de indicação da fita de borda: caractere que é exibido na lagenda da etiquera informando onde esta a borda da peça.
Espessura da linha (px): determina a espessura da linha da imagem.
Largura (px): determina a largura da imagem.
Monocromático: se habilitado a imagem será enviado no modo preto e branco.
Resolução (DPI): medida utilizada pelos fabricantes de impressora para determinar a resolução da imagem impressa.
Rotação (°): define a rotação da imagem em graus.
Tamanho da fonte das cotas (pts): define o tamanho da fonte utilizada nas cotas da peça.
Tamanho do texto da legenda (pts): define o tamanho do texto utilizada nas cotas da peça.
Unidade de medida: convenção utilizada para representar dimensões em Pixels/Pontos ou em milimetros.
Usar referência da fita de borda: para mais informações clique aqui.
Utilizar fontes em negrito: define se o texto é gerado em negrito.
Etiquetas
Copiar imagens das etiquetas para o caminho selecionado: essa opção estando deselecionada faz com que as imagens sejam geradas apenas na pasta BMP_etiquetas do diretório selecionado para geração dos programas. Quando selecionada, as imagens são copiadas também para o caminho selecionado.
Salvar imagens das etiquetas: habilitando o check box para salvar imagens das etiquetas automaticamente é habilitado o campo de caminho da etiqueta, esse campo ao estar em branco como a imagem acima, é enviado no caminho da etiqueta informado ao software, o mesmo caminho indicado no momento da geração dos arquivos, sendo assim o caminho que a máquina utiliza deve ser o mesmo do enviado.
Máquina 1
Gerais
Nome: defina o nome para a máquina.
IMPORTANTE: O nome definido neste campo altera também o nome da pasta onde serão salvos os arquivos gerados.
Comprimento X (mm): o valor inserido neste campo indica o comprimento máximo útil da máquina.
Largura Y (mm): o valor inserido neste campo indica a largura máxima útil da máquina.
Versão do Software TPA: versao de itegraçao do sotware TPA, Esta linha sera aa primeira do valor. Valor padrao: TPA\ALBATROS\EDICAD\02.00:969:r0w0h0s1
Outros
Software de integração: define para qual sistema de integração os programas serão gerados: H80 Flashnest, H80 F4Nest e F4 Integrate.
Ferramentas
Para verificar as configurações sobre Ferramentas CNC, clique aqui.
Fresas
As Fresas são utilizadas para execução de rasgos e usinagens.
Usinagem de Contorno
Direção de corte para usinagens de contorno: define se a usinagem de contorno tem de ser feita no sentido horário ou anti-horário.
Início da usinagem de contorno: define onde é o início da usinagem de contorno, em um dos cantos ou no meio de uma das arestas da peça. Essa opção é aplicável somente as usinagens de contorno externa.
Usinagem interna
Direção de corte para usinagens interna: define se a usinagem interna tem de ser feita no sentido horário ou anti-horário.
Início da usinagem de contorno interna: define onde é o início da usinagem de contorno interna, em um dos cantos ou no meio de uma aresta da usinagem.
Usar direção de corte em operações de uma linha: ao marcar essa configuração, usinagens com uma linha só seguem a direção de corte da fresa. Para mais informações, clique aqui.
Compensação de ferramenta
Alinhamento: define se a ferramenta tem uma compensação, Automático, Centro, Esquerda ou Direita conforme sentido da opção Direção de corte para usinagem de contorno. Para mais informações, clique aqui.
Lado de compensação da ferramenta em relação a geometria de contorno: configura o lado da compensação da ferramenta em relação à geometria de contorno. Esta configuração não afeta os pontos da geometria.
Lado de compensação da ferramenta em relação a geometria interna: define o lado de compensação da ferramenta em relação à geometria interna, centro, esquerda ou direita.
Entrada
Prolongamento da entrada (mm): prolongamento da entrada antes de começar o corte do contorno, equivalente à linha vermelha na imagem.
Tipo da entrada em usinagem linear: define o tipo de entrada que a ferramenta irá utilizar ao realizar usinagens e contornos em formas lineares. Opções Rampa, vertical, circular.
- Circular: neste tipo a ferramenta desce fora da peça e então começa a cortar tangencialmente antes de entrar na peça.
- Vertical: neste tipo a ferramenta desce verticalmente sobre a peça e começa o corte.
- Rampa: neste tipo a ferramenta desce fazendo uma rampa até atingir a profundidade máxima da operação.
Entrada/Saída
Distância entre a entrada e a saída (mm): distância onde a ferramenta sai e entra da peça. É aconselhado que este valor seja maior que zero para que o corte não deixe nenhum fragmento (rebarba).
Propriedades
Altura (mm): altura da ferramenta.
Código: código da ferramenta.
Compensação de perfuração e usinagem passante (mm): compensação da perfuração e usinagem da peça.
Diâmetro (mm): diâmetro da ferramenta.
Fazer usinagem: máquina está habilitada para fazer usinagem.
Nome: nome da ferramenta
Profundidade da passada (mm): profundidade das passadas da ferramenta.
Transpasse (mm): transpasse entre as passadas da ferramenta para evitar sobra de material.
Velocidade de corte (mm/min): velocidade de corte da ferramenta.
Velocidade de perfuração (mm/min): velocidade de perfuração da ferramenta.
Velocidade de rotação (rpm): velocidade de Rotação da ferramenta em RPM.
Saída
Prolongamento da saída (mm): prolongamento de saída após terminar a usinagem/contorno, equivalente à linha vermelha.
Tipo de saída: define o tipo de saída que a ferramenta irá utilizar ao realizar usinagens e contornos.
- No tipo vertical: a ferramenta desce verticalmente sobre a peça e começa o corte.
- No tipo circular: a ferramenta desce fora da peça e então começa a cortar tangencialmente antes e entrar na peça.
- No tipo rampa: a ferramenta desce como uma rampa e começa o corte.
Serras
As serras são utilizadas para execução de rasgos.
Propriedades
Alinhamento: alinhamento da serra, centro, esquerda ou direita.
Código: o código definido neste campo deve estar igual ao cadastro definido na máquina para que a ferramenta possa ser localizada corretamente.
Compensação de entrada (mm): compensação de entrada da serra para executar o corte, em milímetros. Esta configuração é somente aplicada caso o rasgo inicie fora ou sobre o ponto inicial da peça.
Compensação de saída (mm): compensação de saída da serra para executar o corte, em milímetros. Esta configuração é somente aplicada caso o rasgo termine fora ou sobre o ponto final da peça.
Diâmetro (mm): diâmetro da ferramenta.
Espessura (mm): espessura da serra.
Nome: o nome definido neste campo deve estar igual ao cadastro definido na máquina para que a ferramenta possa ser localizada corretamente.
Orientação: orientação da ferramenta, vertical ou horizontal.
Transpasse (mm): transpasse entre as passadas da ferramenta para evitar sobra de material.
Setups
Gerais
Nome: nome do setup da máquina.
Alinhar pela face: define se na geração dos programas é considerada a face de alinhamento cadastrada em cada peça. Se sim esta face será alinhada conforme a configuração selecionada.
Fazer furos: máquina está habilitada para fazer furos.
Fazer rasgos: máquina está habilitada para fazer rasgos.
Fazer usinagem: máquina está habilitada para fazer usinagem.
Considerar sentido do veio: considerar sentido do veio ao gerar os programas nesting.
Fazer nesting: gerar programas para o nesting.
Processos de rasgos: como a máquina processa os rasgos.
Usinar Contorno: define quais dos contornos devem ser executados, sendo as opções:
- Nenhum: usinagem de contorno não será gerada para nenhuma peça.
- Todos: usinagem de contorno será gerada para todas as peças.
- Apenas marcados: usinagem de contorno será gerada apenas para peças que possuem a propriedade Contorno Usinado habilitado no cadastro da biblioteca.
Máquina
Ordem de priorização das operações: define a ordem de priorização das operações para geração de programas. Conforme a ordem indicada neste campo o plugin irá priorizar no programa A a opção selecionada.
Exemplo: Em uma peça que tenha furos em uma face e rasgos na outra face a ordem indicada neste campo irá determinar qual deles será priorizado no programa A.
Ferramentas selecionadas para rasgos: ferramenta usada para rasgos.
Ordem de Operações: ordem que a máquina realiza as operações.
Exemplo: em uma peça que tenha furos e rasgos na mesma face a ordem indicada neste campo irá determinar a sequência em que eles serão executados pela máquina.
Especificações Técnicas
Espessura máxima (Z): espessura máxima da peça que a máquina pode executar operações.
Espessura mínima (Z): espessura mínima da peça que a máquina possa executar operações.
Furos
Broca para furação normal: tipo de broca para furações – Broca Normal, Lança ou escareador.
Broca para furação passante: tipo de broca para furações passantes – Broca Normal, Lança ou escareador.
Broca para furação de marcação: tipo de broca para furação de marcação – Broca Normal, Lança ou escareador.
Profundidade da furação de marcação (mm): profundidade máxima para ser furação de marcação. Quando furo for menor ou igual será automaticamente considerado furo de marcação.
Ângulo da extremidade da broca para furação passante: determine o ângulo da extremidade da broca para uso de furações passantes. (de 25 até 90 graus)
Folga da broca na furação passante (mm): determine a folga da broca para uso em furações passantes.
Diâmetro vertical máximo (mm): diâmetro máximo das brocas verticais.
Número de brocas horizontais (X): quantidade de brocas, para cada face horizontal, presente na máquina.
Número de brocas laterais (Y): quantidade de brocas, para cada face lateral, presente na máquina.
Número de brocas verticais (Z): quantidade de brocas verticais presentes na máquina.
Tipo de brocas: define os códigos usados para cada tipo de broca. Os códigos são definidos nos campos, tipo da broca escareadora, tipo da broca lança, tipo da broca normal e tipo da broca normal grande.