.IMPORTANT:
- The releases are made gradually, so it is possible that your Promob Start is not in the latest version. To receive it, please update your Promob.
- For more information on older versions of Start, click here.
- See the latest updates to the Promob Start library Product Guide here.
NOTES: The Product Guide is constantly updated and it contains all updates according to each version of the library. Consider reading updates from the 1st version to version updates purchased and deployed to your Promob. Versions later than your version are not deployed on your system. If you are interested in purchasing the latest changes, please contact us.
Check out the latest Promob Start news below:
V.13 R.10
Date: 09/14/2023
- Enhancements
Dimensions Configurator
1. Introduced L Bracket as a new option for the front bracket for lower modules, available in the Kitchen, Bathroom, and Bedroom lines. Now, it is possible to change the front bracket option, height, and width of this bracket in the Features Configurator - Specific Line - Structures - Lower - Countertops - Assembly;
NOTES: When activating the joining function, the L Bracket considers a maximum limit of 1800 mm in the total dimension of the bracket since its composition uses pieces with different grain directions that depend on the standard dimensions of the sheet. Therefore, when resizing the module, the join will be made up to 1800 mm.
Hardware
1. Introduced a new option for fixing profile on shelves and partitions. Now, in addition to receiving fixation on the side profiles, on shelves, and on the lower and upper profiles on partitions, they can receive fixation on the rear profile. The improvement was made available for all lines and can be configured in: Hardware and Fasteners - Fasteners - Specific Line - Shelves/Partitions - Parameter F.
NOTE: For the rear profile, the maximum distance settings between the hardware and the type of hardware are unique, so parameters G, H, have been added for the type of hardware and I and J for the maximum distance.
- Corrections
Features Configurator
1. Fixed the situation where the front setback of shelves and partitions in the External Sliding Door Module with Baseboard and Dividers in the Bedroom and Internal Bedroom lines of the Wardrobe Builder was not correct. The default value of the rear divider (L) configuration was changed from 0 to 25.5 mm so that the module's back does not advance. (2033988)
2. Fixed the situation where internal drawers in the Bedroom line did not respect the rear and front clearance attributes of the bottom. (2035816)
3. Fixed the situation where the drawers in Bedside Tables, in the Bedroom line, did not respect the upper clearance configurations.
4. Fixed the situation where the description of the M - Front Base Clearance configuration, located in Features Configurator - Kitchens - Engineering - Structure - High - Eletros Builder - Dimensions / Clearances, did not match the legend image. (2024088)
5. Fixed the situation where the thickness values assigned to internal and external drawers in the Office and Bedroom lines were not correctly respected in the 3D environment, estimates, and technical documentation. (2034947)
6. Fixed the situation where the edge tape application settings were not respected in column modules in the Kitchen line. (2029711 and 2029650)
Wardrobe Builder
1. Fixed the situation where when building a lower module with a hinged door in the Bedrooms line, adding a divider and trying to insert two doors in each opening, the central doors were excluded. (2036212)
Modulation
1. Fixed the situation where the straight corner modules of Cava Kitchens were generated with two left sides. (2030961)
Hardware
1. Fixed the situation where when using divided shelves and bases, the hardware did not respect the external or internal insertion face configuration and inserted more than one type of hardware beyond the configured. (2030270)
2. Fixed the situation where the hardware in column modules in the Kitchen line had incorrect quantities. (2029685)
3. Fixed the situation where the column hardware in the Kitchen line was positioned incorrectly. (2030958)
4. Fixed the situation where the insertion face configuration settings for hardware, internal or external, were not respected in Office tables. (2030274)
5. Fixed the situation where the screws for fixing bottoms appeared in the estimate with zero quantities, making it impossible to import into Cut Pro. (2039106)
Technical Documentation
1. Fixed the situation where when generating a Bar Handle Profile Report, integrated into doors, they were displayed duplicated. (2025142)
Models
1. Fixed the situation where an inconsistency was displayed when inserting bar and point handles on doors. (2036611)
V.13 R.9
Date: 09/04/2023
- Enhancements
Hardware
1. Included the Corner L hardware as a new fastening option for partitions and fixed shelves, available in all product lines.
- From now on, it is possible to change the fixing option and maximum measurement between fixings for shelves and partitions via: Feature configurator > Hardware and fasteners > Fasteners > Specific line > Shelves / Divisions.
- The Corner L can be configured for positioning, depth, and screw diameter in Hardware and Fasteners – Hardware and Fasteners – Corner L.
Features Configurator
1. The images of the Features Configurator have been updated. In the Cabinets - Corners / Counters tab, the described improvements have been implemented. (2030116)
- The description of attribute 'A' has been updated to indicate its relation to corner modules.
- The image available in the Features Configurator has also been updated.
2. In the Wall tab, the following modifications have been made:
- The Side Type attribute has been removed.
- The image in the Features Configurator has been updated.
3. In the Tall tab, the following modifications have been made:
- The description of attribute 'A' has been updated to indicate its relationship with corner modules.
- The image in the Features Configurator has been updated.
Product Spreadsheet
1. Information about the use of screws has been added to the Product Spreadsheet. (2023574)
- Corrections
Features Configurator
1. Corrected the situation where the Back crossbar of the Pantrys/Cabinets/Tall Cabinets in the Kitchen and Office line (Cabinet Builder) did not adhere to the configured dimensions and clearances. (2029465)
2. Corrected the situation where the edge bands of the Back crossbar for Kitchen and Office line Pantrys/Cabinets/Tall Cabinets (Cabinet Builder) did not respect the insertion configurations. (2029465)
3. Added an option to configure the Top Spacing of the Back crossbar for Office line Cabinets/Tall Cabinets modules. (2029465)
4. All images related to edge banding application in the Features Configurator have been updated, and the note Edge band not shown in 3D view has been removed. (2029715)
BEFORE
AFTER
Closets Builder
1. Adjusted the situation where when constructing internal drawers in the Bedroom line, the uprights were inserted with excessive clearance between the separators and the upper shelf. (2027614 and 2035932)
Modulation
1. Corrected the situation where, when changing the orientation of the Front crossbar of the corner L from horizontal to vertical, the Internal Crossbar that was compatible only with the horizontal crossbar was not being removed and remained overlapped with the internal crossbar compatible only with the vertical crossbar. (2025087)
Models
1. Corrigida situação em que não era possível alterar as dimensões de alguns modelos de puxadores de perfis quando aplicados nos módulos. (2015613)
Hardware
1. Corrected the situation where, when using pass-through fasteners, they were inserted into the 3D environment with incorrect quantities. (2023253)
2. Corrected the situation where, when reducing the dimension of the crosspiece, the removal of the second fastening hardware was not performed, resulting in hole overlapping. (2008107)
3. Corrected the situation where the maximum fastening measurement configuration was not respected, and the hardware was inserted in incorrect quantities in Hardware and Fasteners - Fasteners - Bedrooms - Cabinets - 'E'. (2029213)
4. Corrected the issue where the hardware for the internal crosspiece of Blinder Corners did not respect the front and rear positioning parameters in Hardware and Fasteners - Fasteners - Fastener Positioning - 'A' and 'B'. (2029223)
5. Adjusted the situation where the Back item in the Composition tab did not receive the application of hardware. (2030943)
Product Spreadsheet
1. Adjusted the codes and descriptions of Partner FGVTN as follows:
- 51MS1505000A00 - Hinge MS15 Straight 110°;
- 51MS1505150A00 - Hinge MS15 High 110°;
- 51MS1505080A00 - Hinge MS15 Curved 110°;
- 51MS15P5000000 - FGV Automatic Straight Opening;
- 51MS15P5150000 - FGV Automatic Opening High;
- 51MS15P5080000 - FGV Automatic Opening Curved;
- 2 Tubes Trans. + 8 Connectors "T" White 450mm and 500mm - 0076.04W0RB1100;
- 2 Tubes Trans. + 8 Connectors "T" Silver 450mm and 500mm - 0076.04A6RB1100;
- 2 Tubes Trans. + 8 Connectors "T" Inox 450mm and 500mm - 0076.04F0RB1100.
V.13 R.8
Date: 08/17/2023
- Enhancements
Dimension Configurator
1. Added an option to determine whether or not to mark the drilling on the fronts of drawers generated by the screw fixed on the counter front. The visibility of the drilling can be configured through Hardware/Fasteners - Fasteners - Fixation Drawers/Fixation Shoe Rack - I - Screw Drilling Marking on Drawer Front and can be viewed when generating the Technical Drawing.
NOTE: For this improvement, a new attribute has been added to define the depth and diameter of the screw marking in Hardware/Fasteners – Screw.
2. Created an option to define whether the doors will receive handle drilling or not. In the Configurator, it is possible to define the diameter and depth of the drilling. For handle bars, an option has also been provided to define the hole position relative to the center of the handle in the Properties tab.
NOTE: By default, the configuration to generate drilling is set to Yes. To define the hole distances, it is necessary to double-click on the handle to display the configuration in the Properties tab.
3. Reorganized items for Cabinets, Wall, Cabinets, Beds, and Doors/Fronts in the Library and in the Dimension Configurator in the Bedroom line for better interpretation and module location.
BEFORE
AFTER
BEFORE
AFTER
BEFORE
AFTER
BEFORE
AFTER
Models
1. Created an option where it is possible to choose whether sliding doors will have single or double handles. The improvement can be applied to doors with integrated handles or straight doors with handle bars and points.
2. Introduced a new hinge model for straight corners when they do not use an internal crosspiece. The model has variations with and without a damper, as well as a touch latch system for Tip On Door. The improvement was included for Kitchen, Upper Kitchen Cove, and Bedroom lines. (1932326)
Partners
1. Included partner FGVTN. Click here to view the items included in the library.
2. Provided Trunk with and without base in the Bedroom line for the use of the vertical articulator 90º FGVTN Multi.
NOTES:
• By default, a single piston is inserted. When accessing the Aggregates tab, it is possible to define which side it should be applied on.
• When increasing the dimension of the chest, a second piston is added.
3. Included new partner Wurth, for hinges, slides, and lifting systems.
4. Updated finishes of partner Sudati as follows:
• Eleva: American Walnut;
• Soul: Portuguese Basalt and Jasper.
5. Updated finishes of partner Guararapes as follows:
• Colors: Marula, Terrino, Mangue, Perfect Gray, Slate Blue, Erva Mate (Herb);
• Metalic: Naked, Aura, Jasper, Platinum, Tecno;
• Comfort: Tear, Gali;
• Brazilian Woods: Tauari Striped, Curupixá Striped, Freijó Striped;
• Mageo: Mageo Oak, Mageo Honey, Mageo Walnut.
- Corrections
Dimension Configurator
1. Corrected the situation where internal drawers with fronts did not respect the frontal setbacks, and internal drawers without fronts did not have setback configuration in Kitchen, Bedroom, and Office lines. For this correction, default values for frontal setbacks in the Bedroom line were adjusted to be compatible with all door systems, set at 80 for swing doors, 90 for external sliding doors, and 100 for internal sliding doors. (2020320)
2. Fixed an issue where images were displayed in inappropriate places and did not match the configurations available in the Feature Configurator. (2024076)
3. Fixed an issue where the image for the General Assembly configuration - Handles / Profiles - Aluminum Door Profiles did not specify the glass size deduction. The image was replaced to indicate this deduction. (2024100)
4. Fixed an issue where the Lower Base Swing Door Cabinet module in Bedroom did not respect the upper door clearance. For this fix, internal door configurations were removed so that only configurations for Built-in Doors are used. (2021743)
BEFORE
AFTER
5. Fixed an issue where inserting Straight Corner modules with Parallel External Spacer configuration did not position the piece correctly. (2025041)
6. Fixed an issue where upper rear crossbars of straight corners in Kitchens were not removed even when configured not to be inserted in Kitchens – Engineering – Structure - Bottoms/Tops - Corners – Straight Corners/Straight Corner Builder – Assembly. (2021352 and 2022673)
NOTE: The folder name in the Features Configurator for Straight Corners was changed to Straight Corners / Straight Corner Builder.
7. Fixed an issue where a specific internal drawer structure configuration for the Bedroom line was available even when a General Assembly configuration already existed. Reorganization was done so that drawer structure configuration for all lines is done exclusively in General Assembly – Drawers – Structures. (1992877)
BEFORE
AFTER
8. Fixed an issue where the maximum depth configuration for drawers across all lines was not being respected when changing the value through the path Assembly - Drawers - Structures - External/Internal Drawers - D - Maximum Drawer Depth. (2020166)
9. Fixed an issue where corner brackets did not respect the values of back clearances (upper, lower, and lateral). Now, corner brackets without doors can have different clearance values than corner brackets with doors, as they are constructed differently. (2021333)
10. Fixed an issue where configuring Straight Corners in the Kitchen line to not use internal spacers continued to generate spacer holes for blind doors. Additionally, the options for this configuration were removed from the Cove line, which is incompatible, and from incompatible hinges. (2025037)
11. Fixed an issue where the rear setback of shelves in wine rack and niche modules was not respected. (2025061)
12. Fixed an issue where the bottom base of 1D/2D Refrigerator modules in the Kitchen line was inserted with a rear setback, not respecting the setback configurations applied in the Dimension Configurator. (2025052)
13. Fixed an issue where the captions of the image for Concha handle configuration were not consistent with the configurations.
BEFORE
AFTER
14. Fixed an issue where there was no translation in the English language for the Maximum Top Thickness configuration in Panels/Tops/Tamburatos.
Cabinet Builder
1. Fixed an issue where constructing Sliding Doors displayed an error message, causing the system pieces to be displaced. For this situation, default values for light internal sliders were adjusted and the image for the configuration was updated for better interpretation. (2020797)
BEFORE
AFTER
2. Fixed an issue where constructing a module and inserting a Suspended Kit positioned it incorrectly. (2021278)
3. Fixed an issue where profiles for hardware VB35 and VB36 in Bedroom modules were misaligned. (2020302)
4. Fixed an issue where constructing Cabinets with Sliding Internal Doors and External Closure in the Bedroom line resulted in incorrect placement of the base. (2019010)
5. Fixed an issue where hardware for rear crossbars in Bedroom modules was misaligned. (2020309)
7. Fixed an issue where constructing external drawers in the Office line received a frontal setback as if they were internal drawers.
Modulation
1. Fixed an issue so that the module Kitchen - Bottoms - Drawer Units - 2D+ 1D has the same height dimensions as the 4D module when using incremental values. (2023361)
2. Fixed an issue so that when inserting the 3-drawer niche, it is correctly positioned below the top. For this, the default value for inserting the 3-drawer niche was increased to 450 mm.
NOTES: If it is necessary to increase the minimum drawer height value, the insertion values for the niches must also be increased. (1963773)
3. Fixed descriptions of items in some modules in the Kitchen, Bedroom, and Office lines where accented letters "É" and "Ã", as well as "Ç", were replaced by special characters like §, £, and ©. (2020321)
4. Fixed an issue where Upper Niche and Wine Rack modules in the Kitchen and Bathroom lines did not have an upper rear crossbar, unlike other modules in the lines. (2025070)
NOTES: For this fix, configurations for Insertion of Upper Rear Crossbar, Back Pannel Retreat, Upper Back Panel Gap, Back Panel Gap, and Lower Back Panel Gap were divided between modules With Door and Without Door, now individually changed in the Kitchen, Bathroom, and Bedroom lines.
Modeling
1. Fixed an issue where Hafele Invisa GT230 Drawer models with Push & Hafele Invisa PP125 with Push received additional handle models, in addition to Tip On.
Cutting Plan
1. Fixed an issue where applying overcut to thickened tops did not add the value to the crossbars that make up the top. (2021716)
Product Spreadsheet
1. Fixed an issue where the product spreadsheet in Start had edge tape codes that were not the same as those generated in Promob. Additionally, the warning for items without prices for profiles was removed, as it is not necessary to input prices. (2024046)
2. Changed the references of some profiles to avoid duplication when importing into Manager. (2024046)
V.13 R.7
Date: 07/25/2023
- Enhancements
Dimensions Configurator
1. Available the option of Cava handle in MDF in the line of Kitchen Cava for the Lower and Pantry modules. In addition to the handle height settings, the Cava MDF allows for thickness and edge banding adjustments. For the Upper units, there is the option of using or not using the Cava Aluminum handle, as well as the option to recess the base when the handle is not used.
2. Available the option to define the distance between the end of the internal drawers amount and the end of the module in the Kitchens, Bedrooms and Offices lines. This setting can be found in:
- Kitchens: Engineering > Drawers > Retractor > Retractor Rear Distance;
- Bedrooms: Engineering > Drawers > Retractor > Assembly > Retractor Rear Distance;
- Offices: Engineering > Drawers > Retractor > Assembly > Retractor Rear Distance.
3. Included a new configuration option for the fasteners position, subdivided according to the specific lines (1823825). It is now possible to individually set the positioning of the fasteners in:
- Hardware and Fasteners: Fasteners > Fasteners Position, Fasteners Position Shelves, Fasteners Position Back Panels, Fasteners Position Crossbars, Fixation Nails / Clips / Screws.
4. Available new settings to define the Accessories and Hardware code in Assembly - Codes - Accessories and General Assembly - Hardware.
NOTE: When changing the default item codes, it is necessary to update them in the Product Spreadsheet.
5. Available settings to define the maximum depth of external drawers in Assembly General - Structures.
6. Added possibility to remove the front face of the Drawers Internal Non-Fronts available in the modules of the Kitchens, Bedrooms and Offices lines of the Cabinet Builder. Now, the front faces of the drawers without fronts are also removed. This configuration existed for the other drawer models with fronts.
7. Modified the name of the Cabinets folder to Cabinets and Corners for better interpretation in the Bedrooms - Engineering - Structure - Wardrobes / Corners menu. (1999514)
8. Added a new setting that allows changing the thickness of the back crossbars of Sliding Top Cabinets in the Bedroom line. This setting is available in the Dimension Configurator, in Bedrooms - Thicknesses - Boxes - Wardrobes - Wall Sliding - Back Crossbar (I).
9. Included a new configuration that allows to remove the Internal Crossbar for blind corner in the Kitchens, Kitchen Cava and Bedroom lines.
Models
1. Available a new door model in the Provence style. The technical drawing of the door is standard, just like that of a straight door, which means that no separate parts are generated due to the different manufacturing processes. In the budget, the item Provence operation is included to define the additional costs related to the production of the door in Provence style. (1999969; 1803958; 1772643; 1827717; 1889658; 2004566; 1868994, 1914769 and 1817237)
Modulation
1. Added to the Handles tab the Cava Profile options, which are used in the Cava line modules. It is now possible to use them individually. In addition, the handles integrated with door and front models have been reorganized into a specific folder called Integrated. This organization facilitates the location and selection of integrated handles. (2010373)
Cabinets Builder
1. The maximum depth value has been standardized to 1800 mm in the Lower and Upper Kitchen and Kitchen Lateral modules of the Cabinet Builder. (2013357)
Partners
1. Updated the finishes of the Berneck partner with the inclusion of the following finishes. (1958181)
Sense Collection:
- Baru
- Nogal Artezzano
- Taupe
2. Updated the finishes of the partner Arauco with the inclusion of the following finishes. (1978826, 2003284 and 2005041)
Synesthesia Collection:
- Lavender - Matt
- Ocean - Matt
- Bamboo - Nature
- Real Ipe - Trend
- Almond - Bold
- Coast - Bold
- Wood - Vert
- Dew - Vert
- Waterfront - Vert
- Silicon - Vert
3. Completed the inclusion of Duratex partner finishes, as follows:
New Standards:
- Dian Oak - Line Prisma
- Lir Oak - Line Prisma
New Category Internal:
- Aurora - Line Trama
- Gianduja - Line Trama
- Straw - Line Trama
- Titanium - Line Trama
- Dian Oak - Line Prisma
- Lir Oak - Line Prisma
Plugins
1. Realized the association of all parts of the library with the following plugins: (2012511 and 2019355)
- Plugin TekMaq 3020 Mach2 Router
- Plugin Jaragua Compact Eding CNC Router
Product Guide
1. Updated the product spreadsheet, removing items that were out of use and updating incorrect screw codes. It is now possible to view here the document that clarifies where each screw is used in the library. (2010769)
- Corrections
Cabinet Builder
1. Corrected a situation where Shoe Racks with Hinges were opening incorrectly and when the fixings were configured to only have screws, they were not displayed in the environment and on the technical drawings. (2013250)
2. Fixed the situation where, when building internal drawers and resizing the depth of the module, the depth of the drawer amount was incorrect. (2012281)
Materials
1. Fixed a situation where some handles did not change finishes. (2016450)
Integration ERP
1. Corrections were made to the registration of some items to facilitate the integration process between the library and the ERP.
Dimensions Configurator
1. Adjusted the situation where the edge bands of the external separators of the Lower Blind Corner, Upper and Lower Blind Corner Islands were inconsistent with the configuration in Kitchens. (2012987)
2. Adjusted the situation in which the face of the door where it receives the handle did not respect the correct configuration for the application of edge band in the Kitchens line. (2012987 and 2016040)
3. Adjusted the situation in which the side did not respect the same dimension of the retractor external in the Blind Corner Lower Module of Islands, in the line of Kitchens. (2012987)
4. Adjusted the situation where the upper back crossbar of Upper Kitchen cabinets was inserted into the module, even when the setting was set to No, to not insert into the environment. (2016940)
5. Adjusted the situations in which the Upper cabinets of the Kitchen Cava line and Upper cabinets of the Cabinet Builder did not respect the configurations of Back Crossbar Dimension, Back Crossbar Top Distance, Back Crossbar Distance, Back Base Distance, Back Side Distance, Front Side Distance and Back Partition Distance.
6. Adjusted the situation where the description of the door thickness setting on cabinets with flip doors was incorrect in Bedrooms - Thickness - Boxes - Cabinets - Flip Doors, setting H - Doors.
7. Adjusted the situation in which the height configuration of the locker in Corner Cabinets of the Bedrooms line did not correctly respect the measure configured in Bedrooms - Engineering - Structure - Cabinets / Corners - Countertops - Distances / Dimensions, configuration U - Height Locker.
8. Corrected the situation in which the representation of the image of the machining feed configuration of the hollow handle had the incorrect quota position, located in Dimension Configurator - Kitchens - Kitchen Cava - Machining Handle Cava.
9. Corrected the situation where there were in two places different settings to define the depth and diameter of the screws of hinges and slides, and in only one of them the settings were respected. Now, the setting is only in Hardware and Fasteners - Hardware - Screw, settings A and B.
Modulation
1. Fixed the situation where the edges of the Thickened Top (6462) were not displayed in the environment. (2007146)
2. Corrected the situation in which the sides of the Upper Cabinet with Sliding Doors of Internal Lateral Kitchens module were inverted and their translation was incorrect.
IMPORTANT: Corrections No. 3, 4, 5 and 6 included in version V.13 R.7 on 31/07/23:
3. Fixed a situation where the fittings of the column modules available in the Cabinet Builder were positioned incorrectly for both the standard and symmetrical configuration. (2022626)
4. Adjusted the situation in which when changing values of Side and Back Distance of L/ Oblique Corners, the front crossbar of the Oblique Corner module did not correctly respect the configured positioning and dimensioning. (2022601)
5. Corrected the situation where the alignment face of the right side of the telescopic drawer was incorrect. (2022513)
6. Corrected the situation in which it was not possible to add a description in parameter C available in the Dimensions Configurator - Hardware and Fasteners - Hardware - Feet. With this correction, older projects (prior to version V.13 R.7) will be able to be opened correctly in the new version of the library, without deconfigurations or inconformities of reading. (1931455)
Hardware
1. Corrected the situation in which on the bottoms of the Cabinet modules of the Office line the fixing position of the hardware was incorrect. (2012811)
Models
1. Corrected a situation where the External Drawers of the lower modules of the Bedroom line of the Cabinet Builder used the External Drawer models of the Kitchen line.
Cutting Plan
1. Corrected the situation in which when generating the cutting plan of the Built-in Stove Niche modules the plates were sent with a thickness different from the configured one. (2012693)
Partners
1. Corrected the situation in which when generating Cutting Plan or Technical Drawing, pieces with the material Nogueira Florida Horizontal, Duratex-Design, the direction of the shaft was not sent correctly, in addition, the material did not have texture applied. (2008040)
2. Corrected a situation where the dimension of the rear of the Hafele Alto Drawer was incorrect. It has been adjusted to a smaller dimension than the base, according to the measurements in the Hafele technical manual. (2008068)
3. Fixed situation where some items from partner Hafele used standard materials inconsistent with the product.
4. Correction of the translations of the Blum partner's hinges.
V.13 R.6
Date: 06/27/2023
- Enhancements
Dimensions Configurator
1. The reorganization of gap settings for Light Internal Sliding Doors in Kitchens, Bathrooms, and Bedrooms has been made. Now, it is possible to configure the top gap and the bottom gap separately.
Product Guide
1. Adjusted the description of the Product Guide in the Cava Kitchens line, so that the information is clear about the structure of the machined cabinet box, where the cava is made on the sides and not on the doors.
Modulation
1. Added the option for edge banding application to the 6mm and 9mm individual panels through the Properties tab. (1970016)
2. Changed from 176 mm to 186 mm the standard value of the height of the front of the first drawer of the 1G + 1 Drawer Can Holder module in the Kitchen line. This change was made to align the drawers with the other drawer modules.
- Corrections
Dimensions Configurator
1. Fixed the issue where the application of edge banding for the partitions that do not divide the back was not respected, and it was using the edge banding application for partitions that divide the back in Bedroom - Edge Banding - Partitions - Sliding Cabinets without Doors.
2. Fixed the issue where the default value for the backs of the Nightstands was different from the other modules. Now, the default value has been adjusted to remain at 6mm in Bedroom - Thicknesses - Boxes - Nightstands.
3. Fixed the issue where the left side clearance of the back panel was not being applied correctly to the U column cabinets in Bedroom - Engineering - Structure - Cabinets - Dimensions/Clearances.
4. Fixed the issue where the upper and rear clearances of the Rear Crossbars were not being applied in Kitchens - Engineering - Structure - Lower - Base Cabinets Builder - Dimensions/Clearances and Kitchens - Engineering - Structure - Upper - Wall Cabinets Builder - Dimensions/Clearances. (2006457)
5. Fixed the issue where the clearance settings for the back panel of the Upper Cabinets in Kitchens were not being respected in Kitchens - Engineering - Structure - Upper - Wall Cabinets - Dimensions/Clearances. (2004809, 2006982 e 2006986)
6. Fixed the issue where the upper and lower positioning settings of the hinges were not being respected in the Cabinet Builder modules in the Bedroom line under Hardware and Fasteners - Hinges - Drillings. (2003614)
7. Fixed the issue in the Bedroom line where the door clearance configurations were not being respected in Bedroom - Engineering - Clearances - Cabinets. (2006982)
8. Fixed the issue where the image in Portuguese differed from the images in Spanish and English in Kitchens - Engineering - Clearances - Drawers.
Modulation
1. Fixed the issue where the Basc + Gav drawer module was being inserted misaligned with the other cabinets that have a central division in the Kitchens and Bathrooms line. To resolve this, the default value of the flip-up door opening in the Kitchens line was changed from 332.5mm to 376mm, and in the Bathrooms line, it was changed from 324.75mm to 376.5mm.. (2004817)
NOTES: The drawer modules with a flip-up door have the option to configure the height of the flip-up door opening through the Properties tab. Therefore, they are inserted aligned with the other modules with a central division. However, when you change the height of the module, it is necessary to readjust this configuration to ensure they remain aligned with the others.
2. Fixed the issue where the doors of the Straight Corner Islands in the Kitchens line were being inserted with a setback and overlapping the crossbars. To resolve this, the sides were adjusted to align with the external spacer, just like in the Straight Corner Islands of the Cava Kitchens line.
3. Fixed the issue where the hinges in the modules of the Office line were being inserted in the incorrect position, causing them to protrude into the dividers. (2006982)
Budget
1. Corrected the situation where the message Items without price, was displayed when generating the budget of components with the Profile Gola, even when there was a registered price. (2007377, 2007144 e 2004555)
Cabinet Builder
1. Removed the Generic Internal Sliding Door option available on the Upper Cabinets of the Bedroom and Internal Side Bedrooms line. This removal was done because the system is not compatible with the cabinet type, which made it difficult to use the sliding clearance settings in the Dimension Configurator.
Technical drawing
1. Fixed situation where hinge holes were not generated in all modules of the Kitchens line. (2006982)
V.13 R.5
Date: 06/15/2023
- Enhancements
Feature Configurator
1. Available for all lines, new configurations for application of edge band on batten and retractors of the internal drawer uprights.
2. Configuration available to define the retreat back of the shelves and partition that divide the bottom. Now it is possible to identify the setback configuration for shelves and partitions that divide the back, as well as shelves and partitions that do not divide the back.
3. Improvement made to the images available in Distance Corners Cabinets, now represented with a single spacer. (1999975)
4. Modified the location of the Toe kick tab in the Feature Configurator, previously located under General Assembly. It is now located within Assembly - Visibility Conditions.
5. The Distance Corners Cabinets and Distance Corners Wardrobe folders, located in Insert Measures - Bedroom Dimensions, were united into a single Corner Clearance folder, maintaining the organization pattern as used in the Kitchen line. (1999982)
6. Improved the settings image for Honeycomb Sandwich. Now all available settings are shown in the image. (1999941)
Models
1. Including finishing option Fluted Glass H, with horizontal direction and Fluted Glass V with vertical direction, in the glass models.
- Corrections
Features Configurator
1. Fixed the issue where the crossbars and saparators of the internal drawer stiles in all product lines did not consider edge applications. (2003168)
2. Corrected the situation where the image was inconsistent with the captions in Kitchens - Engineering - Structure - Altos - Pantries - Assembly (1999966)
3. Fixed the situation in which the value applied in the configuration to define the lateral clearance of the bottom was not considered. (1995314)
4. Fixed the issue where the Common Runners configuration was not available in Hardware and Fixtures - Hardware. (1999990)
5. Corrigida a situação em que os atributos B, C e K da pasta de Tamburatos - Estrutura disponível no Configurador de Dimensões não eram representados na imagem.
Modulation
1. Fixed the issue where the back panels of the corner did not match the maximum height value of the module. (2000910)
2. Fixed the situation where when inserting Corners with and without Reinforcement and inserting lateral crossbar , the bottom was removed from the module and, in some modules, the horizontal crossbar were not inserted.
Closets Builder
1. Fixed the situation where, when constructing Upper Straight Corners for Internal and External Kitchen and adding shelves, crossbars were being inserted along with the shelves.
Models
1. Fixed the situation where the following handles were inverted in horizontal position 02 (2001397):
- Concha 100, Haste 05, Haste 13, Haste 14, Haste 16, Haste 23, Haste 24, Haste 28, Haste 29, Haste 34, Haste 35, Haste 37 e Haste 39.
Cutting plan
1. Fixed situation where when exporting a composite top to Cut Pro, edge band information was not displayed. (1996614)
Price Configurator
1. Fixed the situation where the standard slides of the system were not displayed in the Price Configurator. (2003044)
Price List
1. Fixed the situation where the incorrect reference for the Toe Kick was being used, and the items were not available in the Price List.
Properties
1. Fixed the situation where the measure A available in the Properties tab for setting the dimension of the front of straight corners, was not respected. (1997110)
V.13 R.4
Date: 06/05/2023
- Enhancements
Features Configurator
1. Updated Plastic Leg 1 to follow the same pattern as the other models. Now it is possible to define its height through a specific attribute, as well as its description.
2. Improved the image of the settings that define the visibility of the baseboards. Now, in addition to the Lower Countertops, the Cabinets and Pantries are also represented. (1999978)
3. Added an enhancement where, in addition to defining the visibility of the rear baseboards, it is now possible to define the visibility or non-visibility of the side and front baseboards.
OBSERVATIONS:
- The Automatic Insertion tool interferes with the use of this configuration, so please check the activation of the baseboards through it.
- When activating the display of the baseboards and then activating the Junction function, it is necessary to reinsert the module for the baseboard junction to take place.
- For Straight Corner modules, due to their usability, only one of the side baseboards respects the side baseboard configuration, while the other respects the rear baseboard configuration, as it is positioned and aligned with the rear baseboard of the module that fits into the corner.
Modulação
1. Updated description and nomenclature of Grooved and Ripped Panels to better identify the panel orientation. (1993067)
- Corrections
Features Configurator
1. Adjusted the situation where the configuration to define the width of the invisible slide was displayed below a tab with a description inconsistent with its function, in Hardware and Fasteners - Hardware - Invisible Slide - General. (1999949)
2. Corrected the situation where in the Lower Sink Cabinet, the clearance between the drawers and doors did not respect the configured clearance values. (1997735)
3. Corrected the situation where when building a cabinet in the builder with 3 doors and a divider between the single door and the double door, the clearance between the doors did not respect the configured central clearance value.(1998654)
Modulation
1. Fixed the situation where it was possible to change the thickness measurement of shelves with any value through the Properties tab. (1996952)
Partners
1. Fixed the issues with the Blum partner: (1997952)
- Incorrect contour box for some Legrabox items.
- A message was displayed when the partner was included in another system.
Budget
1. Fixed the situation where generating a budget for the curved clothes hanger resulted in a unit measurement. Now, the budgeted item is the Curved Clothes Hanger Profile in meters. (1994425)
Cutting Plan
1. Fixed the situation where the Y-Shaped Handles appeared in incorrect quantities when sent to Cut Pro. (1984938)
Accessories
1. Adjusted the situation where the upper modules of Cave Kitchens did not generate junctions for LED Profiles. (1993074)
2. Adjusted the situation where LED Profiles created through grooves and did not respect the Features Configurator. (1993074)
Price List
1. Fixed the situation where the Straightener item was not listed in the price list. (1998469)
2. Fixed the situation where the glass references were different between the Budget and the Start Price List. (1999924)
V.13 R.3
Date: 05/29/2023
- Enhancements
Features Configurator
1. Added new visibility condition attributes, created for the Features Configurator accessories, available in Assembly - Accessories Cabinet Builder - Visibility Condition.
2. Added new dimension insertion restriction attributes for Features Configurator accessories. Thus, it is possible to choose the dimension of the restriction through the settings in Assembly - Accessories Cabinet Builder - Dimensions - Kitchen/ Bedrooms.
3. Available option of Side Panel Retreat, for modules of the lines of Kitchens, Bathrooms, Bedrooms and Offices in the Library and Cabinet Builder. Available in Engineering - Structure - Dimensions/Reveals configurations on all modules.
4. Available in the lines of Kitchens, Kitchens Cava, Bathrooms, Bedrooms and Offices, options for setting the face of insertion of fasteners, being Internal or External fixation, located through the configurations in Hardware and Fasteners - Fasteners - Kitchens/Bedrooms/Bathrooms/Offices - Bases/Sides/Baseboards/Crossbar.
NOTES:
- When changing the type of assembly of the module between Internal Side and External Side, the fixing hardware on the base or side parts is also changed. That is, when mounting with internal side, the part that receives the fixing hardware is the side, and when the assembly is done with external side, the part that receives the fixing hardware is the base.
- When using through hardware and changing the positioning of fasteners, the module will need to be reinserted.
5. Available setting to define the upper distance of the drawer body from the handle for drawers with Profile Y.
6. An option has been added where you can configure the front setback of the shelves. These configurations are located in General Assembly\Setbacks\Front Setback of Shelves.
7. The settings related to closures in cabinets with internal sliding systems have been reorganized. Now it is possible to identify the configurations that are applicable only to closures used in sliding systems or when they are applicable to both types of sliding systems. (1994584)
Cabinet Builder
1. Partial partition option has been made available for the Cabinet Builder modules that have swing doors and partition options. The partition can be resized in Kitchens/Bedrooms/Offices - Engineering - Structures - Dimensions/Distances.
NOTES:
- For correct operation, it is necessary to use the specific shelf for partial partitions. For this, three types of shelves were made available, where each one should be used according to its nomenclature: Left, Central and Right.
-
For the proper functioning of the shelves for partial division in column modules, use the shelf in one of two gaps of the module (one part with full depth or one part with column);
-
By default, in U-column modules, when placing the shelf on the column, due to system limitations, the depth of the shelf is not calculated. This happens because each part of the left, center and right shelf has a different value when using the functionality of joining the pieces, where the depth of one of them is automatically considered. Therefore, they can be small in depth or one different from the other or even all with the maximum depth of the module.
Modulation
1. Four new lower modules for Bedrooms are now available. All of them come with the option of external or internal sides. They can be inserted into the environment through the Cabinet Builder or Library. The configurations can be found in Bedrooms - Engineering - Structure - Countertops - Corners/Counters. Bedrooms - Engineering - Clearances - Countertops. Bedrooms - Engineering - Clearances - Built-in Doors, and Bedrooms - Thickness - Boxes - Countertops/Counters - With Doors.
- Swing Door Counter with Upper Base
- Sliding Door Counter with Upper
- Base Swing Door Counter
- Sliding Door Counter
2. Available in the modules of the Dormitory line, option of plastic feet, which can be inserted through the automatic function, for the items of the Library and through the Components for items of the Cabinet Builder.
3. Added improved edge application. It is now possible to view the raw MDF in the 3D environment where the tape finish is removed.
4. Updated in the Cava line, the images of the Doors/ Fronts, to be smooth without handles.
Materials
1. Included in the Glass options the Corrugated models, available in Materials - Glasses - Miscellaneous - Corrugated.
Partners
1. Available in the partner Duratex new materials, being them the Cinza Fóssil, Gianduia Natural, Moss, Nazca e Quartzo Bienna, available in the line Velluto. In the Design line the new material available is the Nogueira Flórida. (1936877)
Integration ERP
1. Improvements in the registration of all items to facilitate the integration process between the library and the ERP.
Plugins
1. Performed the association of all parts of the library with the following plugins. (196612 e 1991779):
- Plugin Mak Pro 3000 Mach3 Router
- Plugin Rhino RMC 3000 Absolute Mach3 Router
- Plugin Marchiori LD 3000 Mach3 Router
- Plugin Sideco SIR 1325 ATC Router
- Plugin ShopSabre 4896 Router
- Corrections
Features Configurator
1. Fixed the situation in the items Counter Clipping L with and without toeckick in Bedrooms, and Wall Counter Clipping L in Kitchens, where the upper base and rear upper crossbar did not comply with the Rear Setback of the Cabinets, located in Bedrooms - Engineering - Structure - Wardrobes - Dimensions/Reveals and Kitchens - Engineering - Structure - Wall - Wall Wardrobe - Dimensions/Reveals. (1991212)
2. Fixed the situation where in the modules of the Bedroom line, when disabling the Rear Baseboards function, the baseboards remained being inserted improperly. (1991241)
3. Corrected the situation where the retreats of crossbars and bottoms of the Cabinet Builder's Pantry modules were not respected. (1991241)
4. Corrected the situation in the Kitchen line where even when configuring to enable Back crossbar center on Pantry, the batten was not inserted. (1991241)
5. Corrected the situation where the partitions of higher modules of Kitchens, in the Cabinet Builder, did not respect the values configured in the Dimension Configurator. (1987011)
6. Corrected the situation where it was not possible to define the availability of all models of articulators of the partner Blum. Only the visibility of the HK and HKS models was allowed. (1987895)
7. Corrected the situation where the rear setback value in Pantry of Kitchens, was not respected. (1995808)
8. Fixed the situation where some settings available in the Dimension Configurator were provided with incorrect tags, and were not consistent with their respective functions. (1990713)
9. Corrected the situation in the Kitchen and Kitchen Basement line, in which the partitions available in the modules Cabinet Full 3 Doors, Wall Cabinet 3 Doors and 2 Liftup Doors, did not respect the rear setbacks registered in the Feature Configurator. (1990863)
10. Adjusted the nomenclature of the parts and the rotation of the hardware in the image, located in the Feature Configurator - Hardware and Fasteners - Hardware - Uniblock.
11. Corrected the situation where the attributes applicable to the front crossbar of oblique corners were not respected. (1982904)
12. Fixed the situation in the Kitchens line, where settings to set the visibility of the backgrounds in Built-in Stove modules were not respected, located in Kitchens - Engineering - Structure - Built-in Stove - Assembly.
13. Fixed the situation where there was no captioned image for the setting Bathroom - Edge Banding - Views - Closes Modules Cabinets.
14. Fixed the situation in the Kitchen and Bedroom lines, where when using Corners Left without rear reinforcement, the Rear Side Clearance setting was not respected at the bottom/side, making it impossible for the bottom to overlap on the sides. (1995735)
Models
1. Fixed the situation where the actual color of some registered materials was different from the color represented. (1990215)
2. Fixed the situation where point and rod handles were not displayed in the environment. (1992110)
3. Fixed the situation where the Udine Handle was inserted with many faces and did not follow the size of the door. (1975480)
4. Fixed situation where Blum partner hinges were improperly made available for straight corner modules. (1920217)
Hardware
1. Corrected the situation where when inserting drawers without a front, the profile of the hardware was not inserted and did not generate drilling.(1983958)
Cabinet Builder
1. Fixed the situation in the Kitchen line, where when building Top Cabinets, and inserting movable shelves without front recoil, both had the bottom split. (1992841)
2. Fixed the situation in the Dormitory line, where when building Straight Corner Top Cabinets, the upper rear crossbeam was not inserted, even though it was enabled to insert.
Modulation
1. Fixed the situation where in upper modules of the Cabinet Builder the central clearances of doors were not respected. (1988815, 1994030 e 1989618)
2. Fixed the situation where the loose drawer body disappeared when lowering the drawer height. (1988066)
3. Fixed the situation in the Kitchen, Bedroom, and Office lines where the rear sleeper of Upstream 3 was incorrectly executed when choosing to remove it in the configuration. (1991076)
4. Fixed the situation where when accessing the Aggregates tab of the Kitchen and Kitchen Cava drawers, the Cutlery Divider option was not displayed. (1937685)
5. Fixed the situation in the Upper Sliding module in the Kitchens line, where when changing the module assembly to internal side, the hardware fixing was incorrect. (1995337)
6. Corrected the situation in the Dormitory line, where the bases were displaced. (1996247)
Budget
1. Fixed the situation where the reference was duplicated when generating budget for Legrabox model drawers from partner Blum. (1994311)
Cutting Plan
1. Fixed the situation where when being sent to Cut Pro, handles Y were shown in incorrect quantities. (1984938)
Product Sheet
1. Adjusted the references of edge tapes in the product sheet.(1991241)
2. Fixed the situation where no descriptions and references were displayed in the Start Labs Product Sheet related to the 12mm plates available in the library. (1989310)
3. Fixed the situation available in the Start Labs Product Sheet, where the item Divider Frames (Wood) 2420x2700mm Branco Seda, incorrectly used the code of the same item with Cinza Onion finish. (1994319)
V.13 R.2
Date: 04/17/2023
- Enhancements
Features Configurator
1. Added note to clarify the behavior when using entire or divided back crossbar in Closets Builder. (1957635)
2. Modified the names of the A-parameters and their descriptions in Hardware - Hardware - Hinges - Marking Holes, for better understanding. (1972131)
Product Guide
1. Added Slide 36 to exemplify the functionality of thickness edits, combining two or more plates from thickened and composite tops.
2. Added Slide 64 to exemplify and inform the application of the front edge tape individually from the other edge tapes of the part.
- Corrections
Features Configurator
1. Fixed the situation in which the image referring to the application of edge on Sides, in the line Kitchens, was inconsistent and represented the application of tapes on Bases, in Kitchens - Edge Band– Sides – Bottom / Air / Top. (1982025)
2. Corrected the situation where the parameter that defined the distance between the rails for sliding modules in the Bathroom line, was unavailable to configure in the Features Configurator. For the fix, the parameters were reorganized and distributed between structures and gaps within the Bathroom line, in Bathrooms - Engineering - Structures - Sliding Doors and Bathrooms - Engineering - Gaps - Sliding Doors. (1965209)
3. Corrected the situation where the thicknesses of the sides of internal drawers considered 1 mm more than the configured value in the Office and Bedroom lines in Office/Bedroom- Thicknesses - Boxes - Drawers - Internal. (1977309)
4. Fixed situation where upper back crossbars were not removed even when applying the value NO in the Features Configurator. (1980217, 1978701 and 1981991)
5. Corrected the situation where the retreat of Pantry shelves and partitions, from the Closets Builder, did not respect the values applied in the Features Configurator, in Kitchens - Engineering - Structures - Above - Above Building - Assembly. (1981311 and 1981143)
6. Corrected a situation where the values applied for the retreat partition distance in 3-door modules, were not considered, in Kitchens - Engineering - Structure - Above - Above Ground - Dimensions/Adjustment. (1979213)
7. Corrected the situation where when building lower sink counters with vertical partitions, the value for the retreat of the applied partition was not considered, in Kitchens - Engineering - Structures - Inferiores - Sinks - Dimensions/Adjustments. (1977102)
8. Corrected the situation where sliding upper cabinets from the Bedroom line improperly applied the Kitchen line settings, in Kitchens - Structures - Wall Cabinets.
9. Corrected the situation where when building drawers in the Kitchen line with the Amount 1, the gaps between the spacers were not considered according to the measures applied in the Features Configurator and were far from the side, in Kitchens - Engineering - Drawers - Separators. (1973409)
10. Corrected a situation where the central clearance between doors of overhead modules of the Kitchens line was not considered, in Kitchens - Engineering - Clearances - Aerial. (1979889 y 1977059)
11. Corrected the situation where the upper door clearances of the lower modules of the Kitchen line in the Closets Builder were not considered, in Kitchens - Engineering - Clearances - Lower. (1980505)
12. Corrected the situation where the rear shelf clearance was not applied to the upper modules of the Kitchen line in the Cabinet Builder, under Kitchens - Engineering - Structure - Upper - Aerial Builder - Dimensions/Adjustments. (1978684 and 1977996)
13. Fixed the situation where the back were not removed according to the parameter of the Features Configurator applied to Pantry and Wall Cabinets of the Kitchen line in the Closet Builder, in Kitchens - Engineering - Structures - Upper - Pantry Builder - Assembly. (1980228)
14. Fixed issue where upper and lower bases of Bedrooms line Superior Sliding Closets did not consider edge applications correctly, in Bedrooms – Edge Band – Bases – Superior Cabinets.
15. Corrected the situation where several modules of the Bedrooms, Kitchens and Offices line did not consider the back clearance applications correctly, in Kitchens/Bedrooms/Offices - Engineering - Structure - Tops - Dimensions/Adjustments.
16. Corrected the situation where the drilling of the screws did not come out correctly and included a parameter to set the depth of the screw hole in the first part. (1990058 and 1989064).
Models
1. Fixed situation where, when changing the model of the shoe rack to Telescopic sliding shoe rack w/ side crosspiece, the front of the shoe rack was removed. (1930561)
2. Fixed situation where even when applying the value NO for Hafele slide visibility conditions, in the Features Configurator, the templates were displayed. (1980207)
3. Fixed situation where even when applying the value NO for Blum hinge visibility conditions, in the Features Configurator, the templates were displayed. (1980212)
4. Corrected situation where, when inserting corners in the 3D environment, the upper bases were inserted without edgeband finish. (1976214 and 1968438)
5. Corrected the situation where on straight upper cabinet doors, the Concha model handles were inserted in the incorrect position. (1976421)
6. Corrected the situation where when selecting the option Without Counter Front in the Features Configurator, the drawers with telescopic runner model available in the library did not insert the fixing hardware between the sides of the drawer box and its respective front. (1978294)
Closets Builder
1. Corrected the situation where the external sliding doors of the bedroom modules did not consider the limitations and conflicted with the bases.
Budget
1. Adjusted the situation where the edgeband template information for some Composition line items was not displayed correctly. (1976412)
2. Corrected the situation where on systems that are configured not to use budget margin calculation, item prices were displayed without price. (1960526)
3. Adjusted the item code Blum MODUL Hinge Buffer in the Start Labs Product Sheet V.13 R.2, according to the table sent by Blum's partner. (1975228)
V.13 R.1
Date: 03/20/2023
- Enhancements
Features Configurator
1. Reorganization of all settings for better use of the Features Configurator. To view the changes, click here.
2. All images of the Configurator subtitles have been redone so that the understanding of each configuration is understandable and objective.
3. Setting to define width and height of the cutout for invisible sliders has been made available. The changes can be viewed when generating Technical Drawings.
NOTE: The enhancement is compatible when using the Back and Front Tear Type, as Tear.
4. New specific configurations made available for Straight Corners, Oblique Corners, Lower/Superior L Corners, and separated the configurations of aerial and larders of the library and the Builder.
Models
1. New door models were made available: Profile Door, Profile Door 45 + Profile, Profile Door 50 + Profile, Profile Door 60 + Profile and Edge Profile Door + Profile. For these models, it is possible to configure the gap between the panel and the profile.
NOTE: Due to the new door Profile template made available, the handle Profile template is unavailable.
Closets Builder
1. Construction of front-facing internal drawers available for the Kitchens line. The improvement makes it possible to use drawers with fronts in cabinets with built-in doors and receives clearance settings.
ERP Integration
1. Improvements were made to the registration of all items to facilitate the integration process between the library and the ERP.
Product Guide
1. Information on new Profile Door models made available;
2. Provided information about Internal Drawers in Kitchens.
- Corrections
Budget
1. Fixed a situation in which, when generating a quote, the Angle fastener for shelves quoted only one screw. (1971235)
Modulation
1. Fixed the situation in which selecting Single Drawer when disaggregating it generated incorrect construction of the drawer, thus becoming visually incorrect when inserted in the 3D environment. (1959675)
2. Fixed a situation where, when inserting a Clothes Rail rack from the Accessories – Wired line, it became invisible in the 3D environment. (1967694)
Features Configurator
1. Fixed situation in which the indentation of the side of L corners of Kitchens and Bedrooms was incorrectly applied in the background in Kitchen/Bedrooms - Assembly - Structure. The situation caused the backgrounds to become displaced when placed in the 3D environment. (1965343)
2. Fixed the situation where the drawer maximum depth settings were not respected in General Assembly – Drawers – Drawer Structures. (1966815)
Reports
1. Fixed issue where sliding door tracks were not sent to Profiles Report. (1963040)
Technical drawing
1. Fixed the situation in which, when generating technical drawing of telescopic drawers, the fixing holes on the opposite side were not generated. (1968192)
2. Fixed issue where drawer right side edge tape did not tape on correct side. (1971244)
Models
1. Corrected the situation where the option Without front was unavailable for single drawers. (1971992)
Partners
1. The Blum Partner item codes were revised so that they would follow correctly according to the partner's table. In addition, the Legrabox line was made available for pricing in the price table and changes were made in the budget layout, according to the before and after images (1961535 and 1966821)
ERP Integration
1. Corrected the situation where the items of Gola handles were with the incorrect product type structure and were considered as purchased items instead of manufactured items. (1955589)
V.13 R.0
Date: 02/22/2023
- Enhancements
Modulation
1. Added a new led profile located in Accessories - LED Profile, where you can make settings for clearance, slot and dimensions in the Properties tab or the Feature Configurator. In addition, its color can be changed and represented in the rendering, because it has emissive light. For more information about this enhancement, click here.
Feature Configurator
1. Available exclusive configurations for applying edge banding Y Profile doors located in Assembly - Edge Banding - Edge Banding Y Profile Doors. These configurations allow the application or non-application of edge tape on all faces of the door, including the face where the handle is applied.
IMPORTANT: For the handle face, it is important to note that the value applied, Yes/No, overrides the value applied on the respective face where it is used, Top/Bottom/Left/Right.
Product Guide
1. Added on the Accessories slides, specifications about the item Led Profile.
Plugins
1. Performed association of all library parts with the Mach CNC Plugin Machpro. (1955867 and 1970742)
- Corrections
Cabinet Builder
1. Corrected the situation where when constructing Blind Corner Cabinets, the module height was limited to 2700 mm. (1955966)
Feature Configurator
1. Fixed the situation where the door top clearance setting, located in Kitchens - Front/Door Clearances - Bottom - F - Pantry Door Top Clearance, was not applying the values in the Pantry Closets item of the Cabinet Builder. (1948066)
2. Fixed the situation where, in the Bedrooms line, the setting Bedrooms - Assembly - Sliding Door Systems - J - Clearance between Outer Side and Closure, considered only half of the configured value, when using any type of rail on internal sliding doors.
3. Fixed the situation where, in the Bedrooms line, the configuration Bedrooms - Assembly - Sliding Door Systems - B - Sliding Door Discount in relation to the Internal Gap, considered only half of the configured value when using light rails. And it applied only the fixed value of 10 mm when using generic rails on internal sliding doors.
4. Fixed the situation where, on all lines, the configuration, Mounting - Drawers - H - Front Clearance Bottom was not applied when it was configured not to use against front.
5. Fixed the situation where when setting to remove against front in Drawers, the front of the Internal Drawers without front, were also removed improperly.
6. Corrected the situation where when changing the settings of clearances and indentations of the bottom, side, bases and shelves, the values were not respected, in Kitchens - Assembly - Structures, in the configurations Corner/Countertops, Pantry/Supper and Constructor Pantry/Supper (1967460, 1968310 e 1967922) NOTE: Correction released on 03/09/2023.
Hardware
1. Corrected the situation where when building or inserting cabinets with a turning door, the bottom and top bases did not receive fixing hardware.
Partners
1. Corrected the situation where when using the hinge Blum Modul + Damper, and generating technical documents, the description between the Budget and the Warehouse Report, was different. In addition, the hinge was not sent to the Cut Pro shopping list.
1. Corrected the situation where when generating Listing, on the print page, the Minifix rod and drum were not displayed. NOTE: Correction released on 03/09/2023.
Budget
1. Corrected the situation where when generating the budget for Led tapes, the item in unit (UN) added its price to the price of the item in meter (M), instead of considering only the price of the meter. (1969487) NOTE: Correction released on 03/09/2023.